Gunpowder

Gunpowder is a propellant used in firearms, fireworks, and rocket motors. Gunpowder is a low explosive - it burns rapidly without outside air, and in a confined space, will build up enough pressure to cause an explosion. However, it does not detonate in the manner of a high explosive.

History

There are two broad classes of gunpowder, black and smokeless powder. Smokeless powder — a relative term, as it produces some smoke but not dense clouds — has replaced black powder for almost all applications not involving historical reenactment. Modern smokeless powders, of various formulations, are both safer and more powerful than black powder.

Black powder

Black gunpowder was first developed in China, no later than the eleventh century A.D., and possibly earlier. (Early texts are not clear if the mixture described is true gunpowder or not.) It was introduced into Europe in the thirteenth century, through unknown routes. The earliest known description of a true gunpowder formula is in a letter from Francis Bacon to Pope Clement IV in 1267 A.D. By 1275, Albertus Magnus described a formula of four parts saltpeter (potassium nitrate) to one part charcoal (material) and one part sulfur; the chemically ideal proportions are closer to 75% saltpeter, 11.5% sulfur, and 13.5% charcoal.

The earliest European was a finely ground mixture of charcoal, potassium nitrate, and sulfur. This mixture, known as "serpentine powder," tended to absorb moisture, to separate into its components while being transported, and did not burn if packed too tightly into a gun. It gave way in the 15th century to corned powder which was pressed into pellets and screened to a uniform size.

Even with better mechanical formulation, black powder is extremely sensitive to friction and heat, and, while having less explosive power when confined, is far more dangerous to handle than smokeless powder. Aside from its use in historical applications, it still has applications as part of the initiating system of artillery shells.

Smokeless powder

Black powder has gradually been superseded in common use by other propellants which provide higher energy density, lack of smoke, or other desirable properties. In the mid-19th century chemists realized that black-powder smoke wasted fuel, reducing muzzle velocity, while a smokeless powder converted all its fuel, allowing for increased velocity of projectiles. Increased velocity was necessary for rapid-fire shells and in battle against ironclad vessels. In 1884, Frenchman Paul Vieille invented smokeless gunpowder.

Shapes of unburnt grains

Modern smokeless powders are of three basic types:

• single-base propellant: Nitrocellulose and inert ingredients for mechanical properties
• double-base propellant: Nitrocellulose, nitroglycerin or other plasticizer of nitrocellulose, and inert ingredients for mechanical properties
• triple-base propellant: Nitrocellulose, nitroglycerin or equivalent, nitroguanidine, and inert ingredients for mechanical properties

Shape-pressure-time relationships

After mixing the ingredients, smokeless powder is a plastic material that can be cast, extruded, or otherwise made into specific grain shapes and sizes. An actual propellant filling may have a mixture of grain shapes of different propellant types.

• Progressive grains, exemplified by rosettes and multiperforated types, increase the exposed area as they burn, increasing pressure over time
• Neutral grains, such as the perforated forms, expose a constant area
• Digressive grains, represented by cords, decrease the exposed area as they burn, thus decreasing pressure over time

"Grain geometry and burning rate are interrelated. The burning time of a propelling charge that contains a propellant with a high burning rate and strongly digressive grain geometry could be equal to the burning time of a charge that contains a propellant with a low burning rate and strongly progressive grain geometry. European nations have favored the use of single perforation, strip, and cord propellants. The United States uses single perforation and multiperforation propellants. The single perforation grains may be slotted or unslotted. The slotted grain has the desirable characteristic of venting gas during combustion. All countries use ball propellants for small arms." These affect the burning time and the shape of the pressure-versus-time curve.

Burning time is related to the detonation velocity (or deflagration velocity) of the material, and the total surface area of propellant exposed. Grain shape affects the area exposed. Complex shapes allow control of the development of pressure.

Civilian uses

In terms of civilian uses, the technique of gunpowder blasting for mining was first demonstrated by Caspar Weindel at Schemnitz, Lower Hungary in 1627.The practice spread into Harz and Austria in the 1630's, Saxony and Northern Italy in the 1640s and by the 1650s into the Rhineland and Westphalia. It was introduced and developed in Holland and England after the 1660s. It was replaced by dynamite, invented in the late 1860s by Alfred Nobel.

Military Uses

Gunpowder was used as a propellant for rockets, and to propel shot in cannons and Naval guns. During the late 14th and early 15th centuries, Chinese gunpowder technology spread to the whole of Southeast Asia via both the overland and maritime routes, long before the arrival of European firearms. The impact of Chinese firearms on northern mainland Southeast Asia in terms of warfare and territorial expansion was profound.

Technological developments of guns themselves affected the desired characteristics of propellants; advances in propellants allowed developments of new gunnery technologies. Until the 19th century, gunnery was at short range, which allowed short, unrifled barrels. Naval warfare began to push improvements, including rifled, higher-velocity, longer-range cannon to overcome "ironclad" armor. As indirect fire became practical, first on land and then at sea, there was greater demand for longer barrels, which needed both higher-pressure, and later controlled-pressure, propellants.

Land warfare

Sieges were the primary form of warfare in the Middle Ages in Europe. During the period 1346-1500 cannon complemented catapults in siege warfare; only after 1480 did technical improvements in gunpowder and metallurgy render catapults obsolete. Cannons shooting lead, iron or stone projectiles could knock down a castle's high walls, hence the castle had to be abandoned. New fortifications were invented, such as the star shape, such that each wall sloped away from the attacker, reducing the impact of the cannon. One of the main innovators was Italian architect Francesco Di Giorgio, who worked in southern Italy.

Naval warfare

Few technological developments in the history of warfare have been as portentous as the appearance around the turn of the 16th century of effective heavy gunpowder ordnance on shipboard, which began a new era in sea warfare. Employed on Mediterranean war galleys and Portuguese caravels, the weapons marked the solution of a series of daunting technological problems, beginning with the appearance of gunpowder in Europe about 1300. Unlike developments on land, change was at first gradual, but shortly after 1400 the pace of development sharply accelerated to culminate in what may legitimately be termed a revolution in firepower at sea.

To obtain maximum effectiveness from the longer barrel on naval guns, the burning rate of the powder needed to be closely controlled. Much experimentation was performed on the effect of size and shape of powder particles on rate of burning, and larger grains were provided for larger guns. Changes in composition were also experimented with, and in the 1880s brown powder made from under-burnt charcoal was adopted as one means of decreasing the burning rate. A serious drawback of these gunpowders was that only about half of the mixture was converted into gas, the remainder becoming a dense smoke. The French in 1886 adopted smokeless powder made of nitrocellulose (gun-cotton). Four years later, the Royal Navy began using smokeless powder made from a nitroglycerine base. Both these compounds liberated four to five times as much energy as did the black powder used earlier. In addition, these materials could be formed readily into grains so shaped as to control the rate of burning. This gave a uniform pressure, permitting a higher projectile velocity without straining the gun.

At the close of the 19th century, the U.S. Navy followed the lead of the French and adopted a nitrocellulose powder as a propellant charge. This proved reasonably satisfactory until World War II night engagements, when smokeless powder was objectionable because its flash temporarily blinded the ships' crews, as well as giving away the location of the gun and the ship mounting it.

Various flash suppressors were devised and mixed with the powder, which was formed into grains for small guns and into pellets for the larger guns. The British used a multiple-based powder, Cordite N, which was relatively flash-free, but which the U.S. Navy considered to be brittle, unduly sensitive to shock, and hazardous in hot climates. As a result the United States developed other flashless powders and was placing one of them, Albanite, in large scale production at the end of World War II. Triple-base propellants are especially flameless.

Despite the adoption of smokeless powder, black powder still continued in use as a burster charge for projectiles until just before World War I, when more powerful and less sensitive explosives were adopted. In the U.S. Navy, trinitrotoluene (TNT) was adopted for smaller projectiles and Explosive D (ammonium picrate) for the larger ones. These continued in use throughout World War II, although by the end of the war more powerful explosives had come into use, particularly in the smaller antiaircraft projectiles. If the entire spectra of powder uses is considered--torpedoes, mines, aerial bombs, and rockets, as well as large and small projectiles--the trend in explosive development, beginning with the adoption of smokeless powder, was to recognize the special demands of various uses and to formulate specialized compounds tailor-made to particular requirements.