User:John R. Brews/Sample2

In electronic engineering and control theory, step response is the time behavior of the outputs of a general system when its inputs change from zero to a finite value in a very short time. In a more idealized mathematical formulation, the step response of a system in a given initial state consists of the time evolution of its outputs when its control inputs are proportional to Heaviside step functions.

From a practical standpoint, knowing how the system responds to a sudden input is important because large and fast input signals may have extreme effects on the component itself and on other portions of the overall system dependent on this component. In some cases, the overall system cannot act until the component's output settles down to some vicinity of its final state, delaying the overall system response. Formally, the step response of a dynamical system gives information about the stability of the system, and about its ability to reach one stationary state when starting from another.

Description of time-domain behavior

(PD) Image: John R. Brews
Some terms used to describe step response in time domain.

The step response of a system can be described by the following aspects of its time behavior:

• Overshoot: The output swings that extend above the final value
• Undershoot: The output swings that extend below the final value
• Ringing: The alternation of overshoot and undershoot
• Settling time: The time to settle down to remain below a specified amplitude of ringing about the final value
• Rise time: The time to first cross the final value; not necessarily the only time it will cross this value

In the case of linear dynamic systems, much can be inferred about the system from these characteristics. Below, the step response of a simple two-pole amplifier is presented, and some of these terms are illustrated.

Step response of feedback amplifiers

(PD) Image: John R. Brews
Ideal negative feedback model; open loop gain is A_OL and feedback factor is β.

This section describes the step response of a simple negative feedback amplifier shown in the figure. The amplifier when the feedback is disconnected is called the open-loop amplifier. When the amplifier including feedback is meant, it is called the closed-loop amplifier.

The feedback amplifier consists of a main open-loop amplifier of gain A_OL and a feedback loop governed by a feedback factor β. This feedback amplifier is analyzed to determine how its step response depends upon the time constants governing the response of the main amplifier, and upon the amount of feedback used.

Analysis

A negative feedback amplifier has gain given by (see negative feedback amplifier):

$A_{FB}={\frac {A_{OL}}{1+\beta A_{OL}}}\ ,$

where A_OL = open-loop gain, A_FB = closed-loop gain (the gain with negative feedback present) and β = feedback factor. The step response of such an amplifier is easily handled in the case that the open-loop gain has two poles (two time constants, τ₁, τ₂), that is, the open-loop gain is given by:

$A_{OL}={\frac {A_{0}}{(1+j\omega \tau _{1})(1+j\omega \tau _{2})}}\ ,$

with zero-frequency gain A₀ and angular frequency ω = 2πf, which leads to the closed-loop gain:

$A_{FB}={\frac {A_{0}}{1+\beta A_{0}}}$   •   $\ {\frac {1}{1+j\omega {\frac {\tau _{1}+\tau _{2}}{1+\beta A_{0}}}+(j\omega )^{2}{\frac {\tau _{1}\tau _{2}}{1+\beta A_{0}}}}}\ .$

(PD) Image: John R. Brews
Conjugate pole locations for step response of two-pole feedback amplifier; Re(s) = real axis and Im(s) = imaginary axis.

The time dependence of the amplifier is easy to discover by switching variables to s = jω, whereupon the gain becomes:

$A_{FB}={\frac {A_{0}}{\tau _{1}\tau _{2}}}$   •   ${\frac {1}{s^{2}+s\left({\frac {1}{\tau _{1}}}+{\frac {1}{\tau _{2}}}\right)+{\frac {1+\beta A_{0}}{\tau _{1}\tau _{2}}}}}$

The poles of this expression (that is, the zeros of the denominator) occur at:

$2s=-\left({\frac {1}{\tau _{1}}}+{\frac {1}{\tau _{2}}}\right)$

$\pm {\sqrt {\left({\frac {1}{\tau _{1}}}-{\frac {1}{\tau _{2}}}\right)^{2}-{\frac {4\beta A_{0}}{\tau _{1}\tau _{2}}}}}\ ,$

which shows for large enough values of βA₀ the square root becomes the square root of a negative number, that is the square root becomes imaginary, and the pole positions are complex conjugate numbers, either s₊ or s₋; see the figure:

$s_{\pm }=-\rho \pm j\mu \ ,$

with

$\rho ={\frac {1}{2}}\left({\frac {1}{\tau _{1}}}+{\frac {1}{\tau _{2}}}\right)\ ,$

and

$\mu ={\frac {1}{2}}{\sqrt {{\frac {4\beta A_{0}}{\tau _{1}\tau _{2}}}-\left({\frac {1}{\tau _{1}}}-{\frac {1}{\tau _{2}}}\right)^{2}}}\ .$

Using polar coordinates with the magnitude of the radius to the roots given by |s| (See figure):

$|s|=|s_{\pm }|={\sqrt {\rho ^{2}+\mu ^{2}}}\ ,$

and the angular coordinate φ is given by:

$\mathrm {cos} \ \phi ={\frac {\rho }{|s|}}\$   $\mathrm {sin} \ \phi ={\frac {\mu }{|s|}}\ .$

Tables of Laplace transforms show that the time response of such a system is composed of combinations of the two functions:

$e^{-\rho t}\mathrm {sin} (\mu t)\$ $\quad$ and $\quad$ $e^{-\rho t}\mathrm {cos} (\mu t)\ ,$

which is to say, the solutions are damped oscillations in time. In particular, the unit step response of the system is:

$S(t)=1-e^{-\rho t}\ {\frac {\mathrm {sin} \left(\mu t+\phi \right)}{\mathrm {sin} (\phi )}}\ .$

Notice that the damping of the response is set by ρ, that is, by the time constants of the open-loop amplifier. In contrast, the frequency of oscillation is set by μ, that is, by the feedback parameter through βA₀. Because ρ is a sum of reciprocals of time constants, it is interesting to notice that ρ is dominated by the shorter of the two.

Results

(PD) Image: John R. Brews
Step-response of a linear two-pole feedback amplifier; time is in units of 1/ρ, that is, in terms of the time constants of A_OL; curves are plotted for three values of mu = μ, which is controlled by β.

The figure to the right shows the time response to a unit step input for three values of the parameter μ. It can be seen that the frequency of oscillation increases with μ, but the oscillations are contained between the two asymptotes set by the exponentials [ 1 - exp (−ρt) ] and [ 1 + exp (−ρt) ]. These asymptotes are determined by ρ and therefore by the time constants of the open-loop amplifier, independent of feedback.

The phenomena of oscillation about final value is called ringing. The overshoot is the maximum swing above final value, and clearly increases with μ. Likewise, the undershoot is the minimum swing below final value, again increasing with μ. The settling time is the time for departures from final value to sink below some specified level, say 10% of final value.

The dependence of settling time upon μ is not obvious, and the approximation of a two-pole system probably is not accurate enough to make any real-world conclusions about feedback dependence of settling time. However, the asymptotes [ 1 - exp (−ρt) ] and [ 1 + exp (−ρt) ] clearly impact settling time, and they are controlled by the time constants of the open-loop amplifier, particularly the shorter of the two time constants. That suggests that a specification on settling time must be met by appropriate design of the open-loop amplifier.

The two major conclusions from this analysis are:

1. Feedback controls the amplitude of oscillation about final value for a given open-loop amplifier and given values of open-loop time constants, τ₁ and τ₂.
2. The open-loop amplifier decides settling time. It sets the time scale of Figure 3, and the faster the open-loop amplifier, the faster this time scale.

As an aside, it may be noted that real-world departures from this linear two-pole model occur due to two major complications: first, real amplifiers have more than two poles, as well as zeros; and second, real amplifiers are nonlinear, so their step response changes with signal amplitude.

Control of overshoot

(PD) Image: John R. Brews
Step response for three values of α. Top: α = 4; Center: α = 2; Bottom: α = 0.5. As α is reduced the pole separation reduces, and the overshoot increases.

How overshoot may be controlled by appropriate parameter choices is discussed next.

Using the equations above, the amount of overshoot can be found by differentiating the step response and finding its maximum value. The result for maximum step response S_max is:

$S_{max}=1\$ $\ +\ \mathrm {exp} \left(-\pi {\frac {\rho }{\mu }}\right)\ .$

The final value of the step response is 1, so the exponential is the actual overshoot itself. It is clear the overshoot is zero if μ = 0, which is the condition:

${\frac {4\beta A_{0}}{\tau _{1}\tau _{2}}}=\left({\frac {1}{\tau _{1}}}-{\frac {1}{\tau _{2}}}\right)^{2}\ .$

This quadratic is solved for the ratio of time constants by setting x = ( τ₁ / τ₂ )^{1 / 2} with the result

$x={\sqrt {\beta A_{0}}}+{\sqrt {\beta A_{0}+1}}\ .$

Because β A₀ >> 1, the 1 in the square root can be dropped, and the result is

${\frac {\tau _{1}}{\tau _{2}}}=4\beta A_{0}\ .$

In words, the first time constant must be much larger than the second. To be more adventurous than a design allowing for no overshoot we can introduce a factor α in the above relation:

${\frac {\tau _{1}}{\tau _{2}}}=\alpha \beta A_{0}\ ,$

and let α be set by the amount of overshoot that is acceptable.

Figure 4 illustrates the procedure. Comparing the top panel (α = 4) with the lower panel (α = 0.5) shows lower values for α increase the rate of response, but increase overshoot. The case α = 2 (center panel) is the maximally flat design that shows no peaking in the Bode gain vs. frequency plot. That design has the rule of thumb built-in safety margin to deal with non-ideal realities like multiple poles (or zeros), nonlinearity (signal amplitude dependence) and manufacturing variations, any of which can lead to too much overshoot. The adjustment of the pole separation (that is, setting α ) is the subject of frequency compensation, and one such method is pole splitting.

Control of settling time

The amplitude of ringing in the step response in Figure 3 is governed by the damping factor exp ( −ρ t ). That is, if we specify some acceptable step response deviation from final value, say Δ, that is:

$S(t)\leq 1+\Delta \ ,$

this condition is satisfied regardless of the value of β A_OL provided the time is longer than the settling time, say t_S, given by:

$\Delta =e^{-\rho t_{S}}$   or   $t_{S}={\frac {\mathrm {ln} \left({\frac {1}{\Delta }}\right)}{\rho }}=\tau _{2}\ {\frac {2\ \mathrm {ln} \left({\frac {1}{\Delta }}\right)}{1+{\frac {\tau _{2}}{\tau _{1}}}}}\approx 2\ \tau _{2}\ \mathrm {ln} \left({\frac {1}{\Delta }}\right)\ ,$

where the approximation τ₁ >> τ₂ is applicable because of the overshoot control condition, which makes τ₁ = α βA_OL τ₂. Often the settling time condition is referred to by saying the settling period is inversely proportional to the unity gain bandwidth, because 1/( 2π τ₂ ) is close to this bandwidth for an amplifier with typical dominant pole compensation. However, this result is more precise than this rule of thumb. As an example of this formula, if Δ = 1/e⁴ = 1.8 %, the settling time condition is t_S = 8 τ₂.

In general, control of overshoot sets the time constant ratio, and settling time t_S sets τ₂.

Phase margin

(PD) Image: John R. Brews
Bode gain plot to find phase margin; scales are logarithmic, so labeled separations are multiplicative factors. For example, f_0dB = β A₀ × f₁.

Next, the choice of pole ratio τ₁ / τ₂ is related to the phase margin of the feedback amplifier. The procedure outlined in the Bode plot article is followed. To the right is the Bode gain plot for the two-pole amplifier in the range of frequencies up to the second pole position. The assumption behind the plot is that the frequency f_0dB lies between the lowest pole at f₁ = 1 / ( 2π τ₁ ) and the second pole at f₂ = 1 / ( 2π τ₂ ). As indicated in the figure, this condition is satisfied for values of α ≥ 1.

Using the figure the frequency (denoted by f_0dB ) is found where the loop gain βA₀ satisfies the unity gain or 0 dB condition , as defined by:

$|\beta A_{OL}(f_{0db})|=1\ .$

The slope of the downward leg of the gain plot is (20 dB/decade); for every factor of ten increase in frequency, the gain drops by the same factor:

$f_{0dB}=\beta A_{0}f_{1}\ .$

The phase margin is the departure of the phase at f_0dB from −180°. Thus, the margin is:

$\phi _{m}=180^{\circ }-\mathrm {atan} (f_{0dB}/f_{1})-\mathrm {atan} (f_{0dB}/f_{2})\ .$

Because f_0dB / f₁ = βA₀ >> 1, the term in f₁ is 90°. That makes the phase margin:

$\phi _{m}=90^{\circ }-\mathrm {atan} (f_{0dB}/f_{2})$

$=90^{\circ }-\mathrm {atan} \left({\frac {\beta A_{0}f_{1}}{\alpha \beta A_{0}f_{1}}}\right)$

$=90^{\circ }-\mathrm {atan} \left({\frac {1}{\alpha }}\right)$ $=\mathrm {atan} \left(\alpha \right)\ .$

In particular, for case α = 1, φ_m = 45°, and for α = 2, φ_m = 63.4°. Sansen recommends α = 3, φ_m = 71.6° as a "good safety position to start with".

If α is increased by shortening τ₂, the settling time t_S also is shortened. If α is increased by lengthening τ₁, the settling time t_S is little altered. More commonly, both τ₁ and τ₂ change, for example if the technique of pole splitting is used.

As an aside, for an amplifier with more than two poles, the diagram in the figure still may be made to fit the Bode plots by making f₂ a fitting parameter, referred to as an "equivalent second pole" position.

Further reading

• Robert I. Demrow Settling time of operational amplifiers [1]
• Cezmi Kayabasi Settling time measurement techniques achieving high precision at high speeds [2]

• Vladimir Igorevic Arnol'd "Ordinary differential equations", various editions from MIT Press and from Springer Verlag, chapter 1 "Fundamental concepts"