Binary numeral system

The binary number system, also referred to as base-2, or radix-2, represents numbers using only the digits 0 and 1. This is in contrast with the more familiar decimal number system (a.k.a. base-10, radix-10) which uses the digits 0, 1, 2, 3, 4, 5, 6, 7, 8, and 9. In the binary system each digit position represents a power of two. The same number, $10$ represents the value consisting of one set of twos ($2^{1}$) and no sets of ones ($2^{0}$)which is represented by the number 2 in the decimal system. This is equivalent to the decimal system, where each digit position represents a power of ten. The number $10$ represents the value consisting of one set of tens ($10^{1}$), and no sets of ones ($10^{0}$). When the numbering system used for a number is in question, one can write the radix as a subscript to the number as done in the following table.

Binary	$100_{2}=(1\times 2^{2})+(0\times 2^{1})+(0\times 2^{0})=4_{10}+0+0=4_{10}$
Decimal	$100_{10}=(1\times 10^{2})+(0\times 10^{1})+(0\times 10^{0})$

The binary system is used is most electronic computers, as the values of 0 and 1 can be easily represented by a low and a high voltage in a circuit.

Binary arithmetic

Arithmetic with binary numbers is similar to arithmetic with decimal numbers, except that the addition and multiplication tables are much simpler:

$+$ $0$ $1$ $0$ $0$ $1$ $1$ $1$ $10$

$\times$ $0$ $1$ $0$ $0$ $0$ $1$ $0$ $1$

Division and subtraction are performed in the same way as for decimal numbers, but using the corresponding rules for binary addition and multiplication. Non-integer quantities can be represented as binary digits to the right of the binary point. For example, $3/16=0.1875_{10}=0.0011_{2}=(0\times 2^{0})+(0\times 2^{-1})+(0\times 2^{-2})+(1\times 2^{-3})+(1\times 2^{-4})$

Repeating binary expansions also occur, for any fraction where the denominator is not a power of 2. For example, $1/5=0.001100110011_{2}$ (with 0011 repeating).

Irrational numbers can also be expressed, and will have irregular distributions of digits. For example, $\pi =11.001001000011111..._{2}$

Other representations

Because the number of digits in the binary representation of a value can grow quickly, when human readability is desired, binary values are often represented in the octal number system (base 8) or the hexadecimal number system (base 16). Octal uses the digits 0 through 7; hexadecimal uses the digits 0 through 9, followed by the letters A through F to represent the values ten, eleven, twelve, thirteen, fourteen, and fifteen.

Binary numbers can be converted to octal by grouping the binary digits in groups of three beginning at the ones place; each group of three binary digits converts to a single octal digit. Similarly, binary numbers can be converted to hexadecimal by grouping the binary digits in groups of four beginning at the ones place; each group of four binary digits converts to a single hexadecimal digit.

Decimal	Binary	Octal	Hexadecimal
0	0	0	0
1	1	1	1
2	10	2	2
3	11	3	3
4	100	4	4
5	101	5	5
6	110	6	6
7	111	7	7
8	1000	10	8
9	1001	11	9
10	1010	12	A
11	1011	13	B
12	1100	14	C
13	1101	15	D
14	1110	16	E
15	1111	17	F
16	10000	20	10
17	10001	21	11
20	10100	24	14
25	11001	31	19
32	100000	40	20
40	101000	50	28
49	110001	61	31
63	111111	77	3F
99	1100011	143	63